View source for Anycubic i3 Mega

== Support ==
* http://www.anycubic3d.com/support/show/594016.html

== Cura Plugins ==
=== Electric Print Cost Calculator ===
* https://github.com/zoff99/ElectricPrintCostCalculator 

=== Octoprint Plugin ===
* https://github.com/fieldOfView/OctoPrintPlugin

== Start GCODE ==
=== With Nossle Clean ===
 ; CUSTOM START GCODE WITH NOSSLE CLEAN
 ; ORIGINAL ANYCUBIC i3 MEGA STARTCODE (some disabled)
 G21 ;metric values
 G90 ;absolute positioning
 M82 ;set extruder to absolute mode
 M107 ;start with the fan off
 G28 X0 Y0 ;move X/Y to min endstops
 G28 Z0 ;move Z to min endstops
 G1 Z15.0 F{speed_travel} ;move the platform down 15mm
 ;G92 E0 ;zero the extruded length
 ;G1 F200 E3 ;extrude 3mm of feed stock
 ;G92 E0 ;zero the extruded length again
 ;G1 F{speed_travel}
 ;M117 Printing...
 ;G5
 
 ; http://diy3dtech.com/nozzle-cleaning-g-code/
 ; Place as start G-Code in Slicer
 ; Use of this code is at your own risk (no warranties made or implied)
 ;
 M117 Clean			; Indicate nozzle clean in progress on LCD
 ;M109 S<your temp>   		; Uncomment to set your own temp [run warmer to clean out nozzle]
 ; M107				; Turn layer fan off
 ; G21				; Set to metric [change to G20 if you want Imperial]
 ; G90                          ; Force coordinates to be absolute relative to the origin
 G28                          ; Home X/Y/Z axis
 G0 X1 Y0 Z0.15 F9000         ; Move in 1mm from edge and up [z] 0.15mm
 G92 E0                       ; Set extruder to [0] zero
 G1 X100 E50 F500             ; Extrude 100mm filament along Y axis 190mm long to prime and clean the nozzle
 G92 E0                       ; Reset extruder to [0] zero end of cleaning run
 G1 E-3 F500                  ; Retract filiment by 3 mm to reduce string effect
 G1 X3 X100 Z15 F9000         ; Move over and rise to safe Z height
 G1 X3 Y0 Z15 F9000	      ; Move back to front of bed at safe Z height to shear strings
 ;
 ; Ensure extruder is not reset by other code or it will be 3mm short [see next line also]
 ;G1 E3 F500					; Uncomment if you believe exruder will be reset
 ; Recommend turning off SKIRT in the slicer to avoid strings pulled into first layer
 ; Begin printing with sliced GCode after here
 G1 F{speed_travel}
 M117 Printing...
 G5


=== Original ===
 ; ORIGINAL ANYCUBIC i3 MEGA STARTCODE
 G21 ;metric values
 G90 ;absolute positioning
 M82 ;set extruder to absolute mode
 M107 ;start with the fan off
 G28 X0 Y0 ;move X/Y to min endstops
 G28 Z0 ;move Z to min endstops
 G1 Z15.0 F{speed_travel} ;move the platform down 15mm
 G92 E0 ;zero the extruded length
 G1 F200 E3 ;extrude 3mm of feed stock
 G92 E0 ;zero the extruded length again
 G1 F{speed_travel}
 M117 Printing...
 G5

== End Code ==
=== Original ===
 ; ANYCUBIC i3 MEGA END GCODE
 M104 S0 ; turn off extruder
 M140 S0 ; turn off bed
 M84 ; disable motors
 M107
 G91 ;relative positioning
 G1 E-1 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure
 G1 Z+0.5 E-5 ;X-20 Y-20 F{speed_travel} ;move Z up a bit and retract filament even more
 G28 X0 ;Y0 ;move X/Y to min endstops so the head is out of the way
 G1 Y180 F2000
 M84 ;steppers off
 G90
 M300 P300 S4000