Revision as of 09:08, 2 November 2013

Zentyal - the small business server for Linux

Base installation on ubuntu 12.04 LTS

We are startigng with a bare ubuntu system with only ssh enabled.

First of all please update all packages and do some configurations:

vim /etc/apt/sources.list

Uncomment the following line:

deb http://archive.canonical.com/ubuntu precise partner

We install the apt-add-repository-script to be able to use the zentyal repository afterwards and do a full system upgrade:

apt-get install -y python-software-properties
apt-add-repository ppa:zentyal/3.0
apt-get update
apt-get dist-upgrade
apt-get clean

Then add an administrative account for zentyal.

To be able to access the webinterface you have setup an administrativ user which belongs to the admin group. This is NOT the ubuntu adm group! You have to create the group first:

groupadd admin
useradd myAdmin
passwd myAdmin
usermod -G admin -a myAdmin
...

Pleas verify, that the newly created user is part of the new group with:

su my Admin
groups

Finally reboot the system:

reboot

Install Zentyal

The base system then will be install via the command

apt-get -y install zentyal

This will install all prerequisites. Please prepare to have:

the or a mysql root password
the port for the webinterface

I suggest 444 for the webinterface, so it would not be in conflict with https-pages on your site (you can then access the webinterface via http://vserver:444).

Configure the services

You will now be able to access the webinterface via http://vserver:444.

There choose the services you like. It is always good, of possible to to a snapshot after each of this steps and test, if everything went ok!

Firewall

IMPORTANT: Alter your firewall settings to enable the Zentyal administration !!!

Otherwise you won't be able to access the webinterface.

In case you forget this you can temporaryly disable the firewall via commandline and alter this settings.

/etc/init.d/zentyal firewall stop

LDAP port changed on Zentyal 3.2

By default LDAP uses the port 389. The problem is, that samba4 - which is part of Zentyal 3.2 - already uses this port.

For that reason LDAP on Zentyal 3.x is running on port 390. This is not documented on the first sight, and in the firewall, the "LDAP" is assigned to prot 389.

Solution:

add a custom port 390 and name it e.g. LDAP-Zentyal
open the port in the firewall for the internal network traffice (or outside, which is NOT wise)

Test with. Replace <ZENTYAL-SERVER-IP> with the IP of your LDAP-server

ldapsearch -x -p 390 -LLL -h <ZENTYAL-SERVER-IP> -b "" -s base "(objectclass=*)" supportedSASLMechanisms

LDAP

! Be aware and read the [Firewall] section. LDAP on Zentyal 3.x uses port 390 instead of 389 !

On the Users and group page of centyal there are the credentials you need to get readonly access to LDAP.

Basedomain (Base DN): 	dc=your_domain,dc=your_tld
Rootdomain (Root DN): 	cn=zentyal,dc=your_domain,dc=your_tld
Password: 	        <admin_secret_pass>
Read-only root DN: 	cn=zentyalro,dc=your_domain,dc=your_tld
Read-only password: 	<ro_secret_pass>
Default Users DN: 	ou=Users,dc=your_domain,dc=your_tld
Default Groups DN: 	ou=Groups,dc=your_domain,dc=your_tld

For testing you can use e.g. the free and opensource JXplorer or the commandline

ldapsearch -x -p 390 -b "<Basedomain (Base DN)>" -h <IP_OF_LDAP_SERVER> \
-D "<Read-only root DN>" -w "<Read-only password>"

Network

Zentyal completely cares for the network on your ubuntu server.

Therefore you should - but do not have to - disable the network-manager:

sudo service network-manager stop

Create an override file for the upstart job:

echo "manual" | sudo tee /etc/init/network-manager.override

Then configure your network cards with zentyal and be sure to enable the WAN switch, if you are using zentyal on an internetserver without a gateway in front of it, that is, if your server ip is an internet ip address:

Mail

First of all we like to install an e-mail-system. This is what most users want, when they install zentyal on an vserver.

If you only choose the mail plugin, several plugins will be installed, too:

In the next steps, it is important that you

choose eth0 as interface (see picture) and later
DHCP for the configuration of eth0.
Directly afterwards you will be asked for the Kerberos REALM. Please use the domain name of your server, if configured. If not SKIP this step for now!

Virtualisation module moved

Like advised here ...

http://forum.zentyal.org/index.php/topic,17931.0.html

... some of the modules - especially the virtualisation module - have moved to a so called contribution section.

[...]

Moreover, as announced in the Forum, the following modules have been moved to the contrib repositories in order to live

up to our motto of being an easy-to-use Linux small business server:

* PPTP

* Virtualization

* Thin clients

* VoIP

[...]

A solution can be found here:

http://forum.zentyal.org/index.php/topic,18342.0.html

Samba4 - changing the REALM

Sometimes it can be necessary to alter the realm (kerberos). This will brake all user related modules and forces them to reinstall:

/usr/share/zentyal-users/reinstall

Then klick on the "Ally"-Button on the upper right corner of the web-interface.
Then go to "Users" -> "Mode...", change the realm and apply.
Then you have to reenable the "Users"-module and apply the changes.
Then you can also reenable the "Samba"-module and apply the changes.

see: http://trac.zentyal.org/ticket/5695

@@ Line 95: / Line 95: @@
 For testing you can use e.g. the free and opensource [http://jxplorer.org  JXplorer] or the commandline
-  ldapsearch -x -p 390 -b '''"<Basedomain (Base DN)>"''' -h '''<IP_OF_LDAP_SERVER>''' -D '''"<Read-only root DN>"''' -w "ctsJBTgw6gHY6AoRmxCE"
+  ldapsearch -x -p 390 -b '''"<Basedomain (Base DN)>"''' -h '''<IP_OF_LDAP_SERVER>''' \
+ -D '''"<Read-only root DN>"''' -w "<Read-only password>"
 == Network ==

Difference between revisions of "Zentyal"

From Blue-IT.org Wiki