Difference between revisions of "Anycubic i3 Mega"
From Blue-IT.org Wiki
(→With Nossle Clean) |
(→Start GCODE) |
||
| Line 10: | Line 10: | ||
== Start GCODE == | == Start GCODE == | ||
| + | [UPDATE 06/2019 - only works with Cura 3.2] | ||
| + | === With Nossle Clean (Cura 2.6.) and Octoprint 1.3.11 === | ||
| + | First of all: ONLY put the code into Cura! | ||
| + | DO NOT PUT it into Octoprint or both. This would mess things up. | ||
| + | |||
| + | End Codes will remain the same. | ||
| + | |||
| + | ; CUSTOM START GCODE WITH NOSSLE CLEAN | ||
| + | ; Anycubic i3 Mega Scnd. Gen. | ||
| + | ; Put ONLY in Cura 3.6+ and NOT in Octoprint | ||
| + | G21 ;metric values | ||
| + | G90 ;absolute positioning | ||
| + | M82 ;set extruder to absolute mode | ||
| + | M107 ;start with the fan off | ||
| + | G28 X0 Y0 ;move X/Y to min endstops | ||
| + | G28 Z0 ;move Z to min endstops | ||
| + | G1 Z15.0 ;move the platform down 15mm | ||
| + | G28 ; Home X/Y/Z axis | ||
| + | M190 S{material_bed_temperature_layer_0} | ||
| + | M109 S{material_print_temperature_layer_0} | ||
| + | G0 X1 Y0 Z0.15 F9000 ; Move in 1mm from edge and up [z] 0.15mm | ||
| + | G92 E0 ; Set extruder to [0] zero | ||
| + | G1 X100 E50 F500 ; Extrude 100mm filament along Y axis 190mm long to prime and clean the nozzle | ||
| + | G92 E0 ; Reset extruder to [0] zero end of cleaning run | ||
| + | G1 E-3 F500 ; Retract filiment by 3 mm to reduce string effect | ||
| + | G1 X3 X100 Z15 F9000 ; Move over and rise to safe Z height | ||
| + | G1 X3 Y0 Z15 F9000 ; Move back to front of bed at safe Z height to shear strings | ||
| + | M117 Printing... | ||
| + | G5 | ||
| + | |||
=== With Nossle Clean === | === With Nossle Clean === | ||
| + | [UPDATE 06/2019 - only works with Cura 3.2] | ||
| + | |||
; CUSTOM START GCODE WITH NOSSLE CLEAN | ; CUSTOM START GCODE WITH NOSSLE CLEAN | ||
; ORIGINAL ANYCUBIC i3 MEGA STARTCODE (some disabled) | ; ORIGINAL ANYCUBIC i3 MEGA STARTCODE (some disabled) | ||
Revision as of 03:54, 5 June 2019
Contents
Support
Cura Plugins
Electric Print Cost Calculator
Octoprint Plugin
Start GCODE
[UPDATE 06/2019 - only works with Cura 3.2]
With Nossle Clean (Cura 2.6.) and Octoprint 1.3.11
First of all: ONLY put the code into Cura! DO NOT PUT it into Octoprint or both. This would mess things up.
End Codes will remain the same.
; CUSTOM START GCODE WITH NOSSLE CLEAN
; Anycubic i3 Mega Scnd. Gen.
; Put ONLY in Cura 3.6+ and NOT in Octoprint
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 ;move the platform down 15mm
G28 ; Home X/Y/Z axis
M190 S{material_bed_temperature_layer_0}
M109 S{material_print_temperature_layer_0}
G0 X1 Y0 Z0.15 F9000 ; Move in 1mm from edge and up [z] 0.15mm
G92 E0 ; Set extruder to [0] zero
G1 X100 E50 F500 ; Extrude 100mm filament along Y axis 190mm long to prime and clean the nozzle
G92 E0 ; Reset extruder to [0] zero end of cleaning run
G1 E-3 F500 ; Retract filiment by 3 mm to reduce string effect
G1 X3 X100 Z15 F9000 ; Move over and rise to safe Z height
G1 X3 Y0 Z15 F9000 ; Move back to front of bed at safe Z height to shear strings
M117 Printing...
G5
With Nossle Clean
[UPDATE 06/2019 - only works with Cura 3.2]
; CUSTOM START GCODE WITH NOSSLE CLEAN
; ORIGINAL ANYCUBIC i3 MEGA STARTCODE (some disabled)
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{speed_travel} ;move the platform down 15mm
;G92 E0 ;zero the extruded length
;G1 F200 E3 ;extrude 3mm of feed stock
;G92 E0 ;zero the extruded length again
;G1 F{speed_travel}
;M117 Printing...
;G5
; http://diy3dtech.com/nozzle-cleaning-g-code/
; Place as start G-Code in Slicer
; Use of this code is at your own risk (no warranties made or implied)
;
M117 Clean ; Indicate nozzle clean in progress on LCD
;M109 S<your temp> ; Uncomment to set your own temp [run warmer to clean out nozzle]
; M107 ; Turn layer fan off
; G21 ; Set to metric [change to G20 if you want Imperial]
; G90 ; Force coordinates to be absolute relative to the origin
G28 ; Home X/Y/Z axis
G0 X1 Y0 Z0.15 F9000 ; Move in 1mm from edge and up [z] 0.15mm
G92 E0 ; Set extruder to [0] zero
G1 X100 E50 F500 ; Extrude 100mm filament along Y axis 190mm long to prime and clean the nozzle
G92 E0 ; Reset extruder to [0] zero end of cleaning run
G1 E-3 F500 ; Retract filiment by 3 mm to reduce string effect
G1 X3 X100 Z15 F9000 ; Move over and rise to safe Z height
G1 X3 Y0 Z15 F9000 ; Move back to front of bed at safe Z height to shear strings
;
; Ensure extruder is not reset by other code or it will be 3mm short [see next line also]
;G1 E3 F500 ; Uncomment if you believe exruder will be reset
; Recommend turning off SKIRT in the slicer to avoid strings pulled into first layer
; Begin printing with sliced GCode after here
G1 F{speed_travel}
M117 Printing...
G5
Original
; ORIGINAL ANYCUBIC i3 MEGA STARTCODE
G21 ;metric values
G90 ;absolute positioning
M82 ;set extruder to absolute mode
M107 ;start with the fan off
G28 X0 Y0 ;move X/Y to min endstops
G28 Z0 ;move Z to min endstops
G1 Z15.0 F{speed_travel} ;move the platform down 15mm
G92 E0 ;zero the extruded length
G1 F200 E3 ;extrude 3mm of feed stock
G92 E0 ;zero the extruded length again
G1 F{speed_travel}
M117 Printing...
G5
End Code
Original
; ANYCUBIC i3 MEGA END GCODE
M104 S0 ; turn off extruder
M140 S0 ; turn off bed
M84 ; disable motors
M107
G91 ;relative positioning
G1 E-1 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure
G1 Z+0.5 E-5 ;X-20 Y-20 F{speed_travel} ;move Z up a bit and retract filament even more
G28 X0 ;Y0 ;move X/Y to min endstops so the head is out of the way
G1 Y180 F2000
M84 ;steppers off
G90
M300 P300 S4000