Anycubic i3 Mega
From Blue-IT.org Wiki
Contents
Support
Cura Plugins
Electric Print Cost Calculator
Octoprint Plugin
Start GCODE
With Nossle Clean (Cura 2.6.) and Octoprint 1.3.11
[UPDATE 06/2019 - only works with Cura 3.2]
- See bug: https://github.com/Ultimaker/Cura/issues/1036
- This does NOT work (comment out M190/M109) http://blog.mike-greene.com/fixing-cura-temperature-resets/
First of all: ONLY put the code into Cura! DO NOT PUT it into Octoprint or both. This would mess things up.
End Codes will remain the same.
; CUSTOM START GCODE WITH NOSSLE CLEAN ; Anycubic i3 Mega Scnd. Gen. ; Put ONLY in Cura 3.6+ and NOT in Octoprint G21 ;metric values G90 ;absolute positioning M82 ;set extruder to absolute mode M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 ;move the platform down 15mm G28 ; Home X/Y/Z axis M190 S{material_bed_temperature_layer_0} M109 S{material_print_temperature_layer_0} G0 X1 Y0 Z0.15 F9000 ; Move in 1mm from edge and up [z] 0.15mm G92 E0 ; Set extruder to [0] zero G1 X100 E50 F500 ; Extrude 100mm filament along Y axis 190mm long to prime and clean the nozzle G92 E0 ; Reset extruder to [0] zero end of cleaning run G1 E-3 F500 ; Retract filiment by 3 mm to reduce string effect G1 X3 X100 Z15 F9000 ; Move over and rise to safe Z height G1 X3 Y0 Z15 F9000 ; Move back to front of bed at safe Z height to shear strings M117 Printing... G5
With Nossle Clean
[UPDATE 06/2019 - only works with Cura 3.2]
; CUSTOM START GCODE WITH NOSSLE CLEAN ; ORIGINAL ANYCUBIC i3 MEGA STARTCODE (some disabled) G21 ;metric values G90 ;absolute positioning M82 ;set extruder to absolute mode M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{speed_travel} ;move the platform down 15mm ;G92 E0 ;zero the extruded length ;G1 F200 E3 ;extrude 3mm of feed stock ;G92 E0 ;zero the extruded length again ;G1 F{speed_travel} ;M117 Printing... ;G5 ; http://diy3dtech.com/nozzle-cleaning-g-code/ ; Place as start G-Code in Slicer ; Use of this code is at your own risk (no warranties made or implied) ; M117 Clean ; Indicate nozzle clean in progress on LCD ;M109 S<your temp> ; Uncomment to set your own temp [run warmer to clean out nozzle] ; M107 ; Turn layer fan off ; G21 ; Set to metric [change to G20 if you want Imperial] ; G90 ; Force coordinates to be absolute relative to the origin G28 ; Home X/Y/Z axis G0 X1 Y0 Z0.15 F9000 ; Move in 1mm from edge and up [z] 0.15mm G92 E0 ; Set extruder to [0] zero G1 X100 E50 F500 ; Extrude 100mm filament along Y axis 190mm long to prime and clean the nozzle G92 E0 ; Reset extruder to [0] zero end of cleaning run G1 E-3 F500 ; Retract filiment by 3 mm to reduce string effect G1 X3 X100 Z15 F9000 ; Move over and rise to safe Z height G1 X3 Y0 Z15 F9000 ; Move back to front of bed at safe Z height to shear strings ; ; Ensure extruder is not reset by other code or it will be 3mm short [see next line also] ;G1 E3 F500 ; Uncomment if you believe exruder will be reset ; Recommend turning off SKIRT in the slicer to avoid strings pulled into first layer ; Begin printing with sliced GCode after here G1 F{speed_travel} M117 Printing... G5
Original
; ORIGINAL ANYCUBIC i3 MEGA STARTCODE G21 ;metric values G90 ;absolute positioning M82 ;set extruder to absolute mode M107 ;start with the fan off G28 X0 Y0 ;move X/Y to min endstops G28 Z0 ;move Z to min endstops G1 Z15.0 F{speed_travel} ;move the platform down 15mm G92 E0 ;zero the extruded length G1 F200 E3 ;extrude 3mm of feed stock G92 E0 ;zero the extruded length again G1 F{speed_travel} M117 Printing... G5
End Code
Original
; ANYCUBIC i3 MEGA END GCODE M104 S0 ; turn off extruder M140 S0 ; turn off bed M84 ; disable motors M107 G91 ;relative positioning G1 E-1 F300 ;retract the filament a bit before lifting the nozzle to release some of the pressure G1 Z+0.5 E-5 ;X-20 Y-20 F{speed_travel} ;move Z up a bit and retract filament even more G28 X0 ;Y0 ;move X/Y to min endstops so the head is out of the way G1 Y180 F2000 M84 ;steppers off G90 M300 P300 S4000
Calibrating extruder
- http://sturm.selfhost.eu/wordpress/tronxy-x5sa-24v-extruder-kalibrieren-unter-nutzung-der-erweiterten-gcodes/
- https://www.thingiverse.com/groups/anycubic-i3-mega/forums/general/topic:31353
I got an updated extruder for my i3 mega - the one of the i3Mega S. I did not want to flash my firmware, so I had to to calibrate the extruder.
It took me a while, until I recognized, the sending M92 Exxx codes to the printer had no effect. I googled a lot and found out, that the printer works with another subset of gcodes:
The whole idea is to set a "multiplicator" value instead of a fixed one. The command is
M8011 S0.002 ; set multiplicator to 0.002 M8500 ; save to EEPROM
That was my starting point get exact 100mm of filament out of the extruder. The formula to precice the solution is:
new multiplicator = ( messured value (mm) / [1] ) * [2]
[1] filament length reference value in mm - here 100mm [2] the acual messured value, that went through the extruder - here 0.002 (our starting point)
Do this until [2] = [1] :-) Voilà.